一.概述：
为郾城等地区用户提供了全套网页设计制作服务，及郾城网站建设行业解决方案。主营业务为成都网站设计、
成都网站建设、郾城网站设计，以传统方式定制建设网站，并提供域名空间备案等一条龙服务，秉承以专业、用心的态度为用户提供真诚的服务。我们深信只要达到每一位用户的要求，就会得到认可，从而选择与我们长期合作。这样，我们也可以走得更远！
实际工作中估计会碰到需要用一台ASA接两家ISP线路，比如电信和网通，而又没有足够的预算买负载均衡设备，但是又想实现链路负载分担和自动切换，从电信来的流量，从电信线路回去，从网通来的流量从网通线路回去，当其中一条线路出现故障时，所有的流量从没有出现故障线路走。
二.基本思路：
A.用OSPF模拟运营商网络，主要是为了不想手工添加路由
B.通过添加默认路由走电信线路、监控电信线路的网关，和高metric的默认路由走网通线路，实现：
----电信来的流量走电信回去（需要C手工配置网通静态路由相配合）
----电信链路出现故障时，走网通线路
C.通过添加网通的静态路由走网通线路，并监控网通线路的网关，实现：
----网通来的流量走网通回去
----网通链路出现故障时，走电信线路的默认路由
D.对于静态NAT,实际环境只有当两条ISP线路都正常时，才会同时能被访问
E.测试环境，实现静态NAT当一条线路出现故障时，还能同时被访问，实现的方法是：
---ASA两个外部接口配置两条静态NAT
---ASA两个相连的ISP路由器把另外一家ISP所NAT的网段发布出去，并将metric设置比OSPF默认的大
三.测试拓扑：
四.基本配置：
A.R1：
①接口配置：
interface Loopback0
ip address 1.1.1.1 255.255.255.0
interface Loopback61
ip address 61.1.3.1 255.255.255.0
ip ospf network point-to-point
interface Loopback202
ip address 202.100.3.1 255.255.255.0
ip ospf network point-to-point
interface FastEthernet0/0
ip address 202.100.2.1 255.255.255.0
no shut
interface FastEthernet0/1
ip address 61.1.2.1 255.255.255.0
no shut
②路由配置:
router ospf 1
router-id 1.1.1.1
passive-interface default
no passive-interface FastEthernet0/0
no passive-interface FastEthernet0/1
network 61.1.2.1 0.0.0.0 area 0
network 61.1.3.1 0.0.0.0 area 0
network 202.100.2.1 0.0.0.0 area 0
network 202.100.3.1 0.0.0.0 area 0
B:R2：
①接口配置：
interface Loopback0
ip address 2.2.2.2 255.255.255.0
interface FastEthernet0/0
ip address 202.100.1.2 255.255.255.0
no shut
interface FastEthernet0/1
ip address 202.100.2.2 255.255.255.0
no shut
interface FastEthernet1/0
ip address 23.1.1.1 255.255.255.252
no shut
②路由配置：
router ospf 1
router-id 2.2.2.2
log-adjacency-changes
passive-interface default
no passive-interface FastEthernet0/1
no passive-interface FastEthernet1/0
network 23.1.1.1 0.0.0.0 area 0
network 202.100.1.2 0.0.0.0 area 0
network 202.100.2.2 0.0.0.0 area 0
C.R3:
①接口配置：
interface Loopback0
ip address 3.3.3.3 255.255.255.0
interface FastEthernet0/0
ip address 61.1.1.3 255.255.255.0
no shut
interface FastEthernet0/1
ip address 61.1.2.3 255.255.255.0
no shut
interface FastEthernet1/0
ip address 23.1.1.2 255.255.255.252
no shut
②路由配置：
router ospf 1
router-id 3.3.3.3
passive-interface default
no passive-interface FastEthernet0/1
no passive-interface FastEthernet1/0
network 23.1.1.2 0.0.0.0 area 0
network 61.1.1.3 0.0.0.0 area 0
network 61.1.2.3 0.0.0.0 area 0
D.ASA842:
①接口配置：
interface GigabitEthernet0
nameif Inside
security-level 100
ip address 10.1.1.10 255.255.255.0
no shut
interface GigabitEthernet1
nameif Outside
security-level 0
ip address 202.100.1.10 255.255.255.0
no shut
interface GigabitEthernet2
nameif Backup
security-level 0
ip address 61.1.1.10 255.255.255.0
no shut
②两条线路的动态PAT配置：
object network inside_net
subnet 0.0.0.0 0.0.0.0
object network inside_any
subnet 0.0.0.0 0.0.0.0
object network inside_net
nat (Inside,Outside) dynamic interface
object network inside_any
nat (Inside,Backup) dynamic interface
③两条线路的静态NAT配置：
object network Inside_host_outside
host 10.1.1.4
object network Inside_host_backup
host 10.1.1.4
object network Outside-to-backup
host 10.1.1.4
object network Backup-to-outside
host 10.1.1.4
object network Inside_host_outside
nat (Inside,Outside) static 202.100.1.4
object network Inside_host_backup
nat (Inside,Backup) static 61.1.1.4
object network Outside-to-backup
nat (Inside,Outside) static 61.1.1.4
object network Backup-to-outside
nat (Inside,Backup) static 202.100.1.4
----每条线路配置两条NAT,保证一条ISP线路出现故障时，两条静态NAT都能被访问
④防火墙策略配置：
class-map ALL_IP
match any
policy-map global_policy
class inspection_default
inspect icmp
class ALL_IP
set connection decrement-ttl
service-policy global_policy global
access-list outside extended permit icmp any any
access-list outside extended permit udp any any range 33434 33523
access-list outside extended permit tcp any object Inside_host_outside eq telnet
access-group outside in interface Outside
access-group outside in interface Backup
E:R4:
①接口配置：
interface Loopback0
ip address 192.168.1.4 255.255.255.0
interface FastEthernet0/0
ip address 10.1.1.4 255.255.255.0
no shut
②路由配置：
ip route 0.0.0.0 0.0.0.0 10.1.1.10
③telnet配置：
line vty 0 4
password cisco
login
五.ASA842 SLA及路由配置：
①sla配置：
sla monitor 1
type echo protocol ipIcmpEcho 202.100.1.2 interface Outside
frequency 10
sla monitor schedule 1 life forever start-time now
sla monitor 2
type echo protocol ipIcmpEcho 61.1.1.3 interface Backup
frequency 10
sla monitor schedule 2 life forever start-time now
②track配置：
track 1 rtr 1 reachability
track 2 rtr 2 reachability
③静态路由配置：
route outside 0 0 202.100.1.2 1 track 1
route backup 0 0 61.1.1.3 254
---默认路由走电信线路，当电信线路出现故障时自动切换到网通线路
route Backup 61.1.2.0 255.255.255.0 61.1.1.3 1 track 2
route Backup 61.1.3.0 255.255.255.0 61.1.1.3 1 track 2
---当网通线路正常时，到网通的网络的数据走网通的线路，否则走电信的默认路由
route Inside 192.168.1.0 255.255.255.0 10.1.1.4 1
---增加一条回指路由
六.关于静态NAT：
---为了使两条线路其中一条线路出现故障时，两个被静态NAT地址都能访问，需要：
A.每条线路配置两条静态NAT
----前面已经配置
B.每个相连的ISP路由器把另外一家ISP所NAT的网段发布出去，并将metric设置比ospf默认的大
----这种情况在实际环境基本无法实现，两家ISP不可能会帮客户做这样的事情，除非给的费用足够多
----测试环境下还是可以玩一玩的
①R2路由器：
ip route 61.1.1.0 255.255.255.0 202.100.1.10 254 tag 10
route-map ASA842 permit 10
match tag 10
router ospf 1
redistribute static metric 130 subnets route-map ASA842
②R3路由器：
ip route 202.100.1.0 255.255.255.0 61.1.1.10 254 tag 10
route-map ASA842 permit 10
match tag 10
router ospf 1
redistribute static metric 130 subnets route-map ASA842
七.效果测试：
A.线路正常的情况下：
R4#traceroute 202.100.3.1 source l0
Type escape sequence to abort.
Tracing the route to 202.100.3.1
1 202.100.1.2 160 msec 108 msec 56 msec
2 202.100.2.1 36 msec * 24 msec
R4#traceroute 61.1.3.1 source l0
Type escape sequence to abort.
Tracing the route to 61.1.3.1
1 61.1.1.3 112 msec 8 msec 0 msec
2 61.1.2.1 112 msec * 68 msec
---去电信的流量走电信，去网通的流量走网通
R1#traceroute 202.100.1.4 source l202
Type escape sequence to abort.
Tracing the route to 202.100.1.4
1 202.100.2.2 32 msec 56 msec 20 msec
2 202.100.1.10 40 msec * 24 msec
3 202.100.1.4 80 msec * 16 msec
R1#traceroute 202.100.1.4 source l61
Type escape sequence to abort.
Tracing the route to 202.100.1.4
1 202.100.2.2 140 msec 180 msec 80 msec
2 202.100.1.10 64 msec * 88 msec
3 202.100.1.4 140 msec * 84 msec
R1#traceroute 61.1.1.4 source l61
Type escape sequence to abort.
Tracing the route to 61.1.1.4
1 61.1.2.3 116 msec 32 msec 0 msec
2 61.1.1.10 4 msec * 4 msec
3 61.1.1.4 208 msec * 128 msec
R1#traceroute 61.1.1.4 source l202
Type escape sequence to abort.
Tracing the route to 61.1.1.4
1 61.1.2.3 8 msec 120 msec 192 msec
2 61.1.1.10 0 msec * 20 msec
3 61.1.1.4 152 msec * 204 msec
----两个被静态NAT地址都能被访问，并且电信的地址走电信接口，网通的地址走网通的接口
B.电信线路不正常的情况下：
R4#traceroute 202.100.3.1 source l0
Type escape sequence to abort.
Tracing the route to 202.100.3.1
1 10.1.1.10 188 msec * 28 msec
2 61.1.1.3 44 msec 0 msec 0 msec
3 61.1.2.1 108 msec * 84 msec
R4#traceroute 61.1.3.1 source l0
Type escape sequence to abort.
Tracing the route to 61.1.3.1
1 10.1.1.10 0 msec * 20 msec
2 61.1.1.3 100 msec 32 msec 0 msec
3 61.1.2.1 108 msec * 72 msec
---去电信和网通的流量都走网通
R1#traceroute 202.100.1.4 source l202
Type escape sequence to abort.
Tracing the route to 202.100.1.4
1 61.1.2.3 4 msec 184 msec 52 msec
2 61.1.1.10 0 msec * 0 msec
3 202.100.1.4 152 msec * 12 msec
R1#traceroute 202.100.1.4 source l61
Type escape sequence to abort.
Tracing the route to 202.100.1.4
1 61.1.2.3 36 msec 4 msec 16 msec
2 61.1.1.10 200 msec * 16 msec
3 202.100.1.4 184 msec * 148 msec
R1#traceroute 61.1.1.4 source l61
Type escape sequence to abort.
Tracing the route to 61.1.1.4
1 61.1.2.3 48 msec 0 msec 0 msec
2 61.1.1.10 4 msec * 32 msec
3 61.1.1.4 148 msec * 180 msec
R1#traceroute 61.1.1.4 source l202
Type escape sequence to abort.
Tracing the route to 61.1.1.4
1 61.1.2.3 76 msec 52 msec 0 msec
2 61.1.1.10 0 msec * 16 msec
3 61.1.1.4 172 msec * 112 msec
----电信和网通被静态NAT的地址都能被电信和网通的用户访问
C.网通线路不正常的情况下：
R4#traceroute 202.100.3.1 source l0
Type escape sequence to abort.
Tracing the route to 202.100.3.1
1 10.1.1.10 8 msec * 28 msec
2 202.100.1.2 108 msec 72 msec 84 msec
3 202.100.2.1 88 msec * 128 msec
R4#traceroute 61.1.3.1 source l0
Type escape sequence to abort.
Tracing the route to 61.1.3.1
1 10.1.1.10 0 msec * 76 msec
2 202.100.1.2 112 msec 96 msec 24 msec
3 202.100.2.1 248 msec * 76 msec
---去电信和网通的流量都走电信
R1#traceroute 202.100.1.4 source l202
Type escape sequence to abort.
Tracing the route to 202.100.1.4
1 202.100.2.2 4 msec 156 msec 76 msec
2 *
202.100.1.10 40 msec *
3 202.100.1.4 68 msec * 24 msec
R1#traceroute 202.100.1.4 source l61
Type escape sequence to abort.
Tracing the route to 202.100.1.4
1 202.100.2.2 92 msec 60 msec 124 msec
2 202.100.1.10 4 msec * 36 msec
3 202.100.1.4 152 msec * 60 msec
R1#traceroute 61.1.1.4 source l61
Type escape sequence to abort.
Tracing the route to 61.1.1.4
1 202.100.2.2 32 msec 136 msec 116 msec
2 202.100.1.10 80 msec * 56 msec
3 61.1.1.4 120 msec * 120 msec
R1#traceroute 61.1.1.4 source l202
Type escape sequence to abort.
Tracing the route to 61.1.1.4
1 202.100.2.2 4 msec 140 msec 112 msec
2 202.100.1.10 64 msec * 64 msec
3 61.1.1.4 156 msec * 80 msec
----电信和网通被静态NAT的地址都能被电信和网通的用户访问
附件：http://down.51cto.com/data/2363080
另外有需要云服务器可以了解下创新互联scvps.cn，海内外云服务器15元起步，三天无理由+7*72小时售后在线，公司持有idc许可证，提供“云服务器、裸金属服务器、高防服务器、香港服务器、美国服务器、虚拟主机、免备案服务器”等云主机租用服务以及企业上云的综合解决方案，具有“安全稳定、简单易用、服务可用性高、性价比高”等特点与优势，专为企业上云打造定制，能够满足用户丰富、多元化的应用场景需求。
当前题目：ASA842双链路SLA配置测试-创新互联
当前地址：
http://cdkjz.cn/article/pgjcc.html
